R&B Fabrications HS-200 Hose Strap Field Manual | SOP for 200ft Attack Line Carrier

How to Guides - Product Field Manual SOPs - Luminary Global

R&B Fabrications HS-200 Hose Strap Field Manual | SOP for 200ft Attack Line Carrier

Category: Anchor Lines & Ropes

Difficulty Level: Tier 3: Field Competency Required

Complete Field Manual - FREE

Download the official step-by-step PDF guide.

📥 Download PDF Guide

Written by: Valerie Ellis Lavin

Quick Overview

The R&B Fabrications HS-200 Hose Strap is a 200-foot attack line carrier that enables one or two firefighters to transport and rapidly deploy a pre-loaded 1¾-inch hose bundle in commercial, multi-family, standpipe, and rural fire operations requiring extended setbacks from the apparatus.

The HS-200 converts a loose, unmanaged 200-foot hose load weighing approximately 80 to 100 pounds dry into a single, field-ready unit. A reinforced nylon structural spine distributes weight evenly across the bundle, preventing sagging and maintaining integrity during transport. Four 2-inch webbing straps with hook-and-loop closures compress the hose tightly against the spine, while integrated 3M reflective trim enhances operator visibility in low-light and smoke-filled environments. This system is designed for deployment in any scenario where apparatus placement cannot close the distance to the point of entry.

The deployment protocol is a three-step sequence: load the carrier using an accordion or horseshoe fold with the nozzle positioned at the top, transport the bundle to the point of entry using the two-person carry as the standard method, and release all four quick-release tabs simultaneously to drop the carrier and flake the line. The two-person carry, with each firefighter grasping one molded rubber handle, is the preferred method for any distance exceeding a confined-space short drag. Water should not be called for until the line is fully flaked and clear of kinks.

Readiness sustainment requires post-incident inspection of all stitching, nylon webbing, molded handles, and hook-and-loop fasteners before the carrier is returned to service. Velcro closures must remain free of mud, debris, and hydrocarbons to maintain holding strength. The carrier must be air-dried completely before storage and kept away from fuels, oils, sharp tools, and direct sunlight in a protected apparatus compartment.

Field Application Steps

1. PREPARE THE CARRIER FOR LOADING: Lay the HS-200 spine-down on a flat surface with all four security straps fully open and unobstructed. Confirm the carrier is clean, dry, and that all hook-and-loop fasteners are free of debris before loading.

2. LOAD THE HOSE BUNDLE: Load 200 feet of 1¾-inch hose using an accordion or horseshoe fold, positioning the nozzle and first coupling at the top of the bundle so they are accessible immediately upon deployment.

3. SECURE THE STRAPS: Fasten the two innermost straps first, then work outward to the two outer straps. Cinch each strap as tightly as possible to achieve maximum hook-and-loop engagement and prevent hose shifting during transport.

4. CONFIRM BUNDLE SECURITY: Lift the loaded carrier slightly off the ground and verify there is no significant hose movement or shifting within the bundle. If shifting is detected, re-cinch the straps before proceeding.

5. TRANSPORT TO THE DEPLOYMENT POINT: Position two firefighters on opposite sides of the bundle, each grasping one molded rubber handle. Lift on a coordinated command using the legs, not the back, and carry at waist height to the point of entry. In confined spaces where two-person carry is not feasible, a single-operator drag may be used for short distances only.

6. ORIENT THE BUNDLE AT THE POINT OF ENTRY: Place the bundle on the ground with the nozzle end oriented toward the entry point and the supply line end oriented back toward the apparatus. This orientation ensures the line runs in the correct direction when flaked.

7. EXECUTE THE QUICK RELEASE: Grasp all four quick-release tabs simultaneously. In a single forceful motion, pull all tabs outward at the same time. The carrier will fall away from the hose bundle instantly.

8. CLEAR THE CARRIER: Immediately move the empty hose strap out of the primary ingress and egress path. The empty carrier is a significant trip hazard on the fireground and must not be left in the working area.

9. ADVANCE AND FLAKE THE LINE: The nozzle firefighter advances toward the entry point while the backup firefighter flakes out the remaining hose to eliminate all kinks. Do not call for water until the line is fully extended, flaked, and confirmed clear.

Equip Yourself: R&B 200 Foot Hose Strap – Maximum Capacity Attack Line Carrier

Ensure you have the right gear before an emergency strikes.

View Product

LEGAL DISCLAIMER & SAFETY WARNING:
The information provided in this Luminary Global Field Manual is strictly for educational and informational purposes. It is not a substitute for formal medical, tactical, or professional training. In the event of a medical emergency, immediately seek professional help or contact emergency services. Luminary Global assumes no liability for the misuse of equipment, improper application of techniques, or any injuries/damages resulting from the use of these guidelines. Always rely on your official agency training, local laws, and established protocols during a crisis.