StatPacks G3+ Perfusion: Field Manual & SOP

How to Guides - Product Field Manual SOPs - Luminary Global

StatPacks G3+ Perfusion: Field Manual & SOP

Category: Backpacks

Difficulty Level: Tier 4: Professional or Advanced Training Required

Complete Field Manual - FREE

Download the official step-by-step PDF guide.

📥 Download PDF Guide

Written by: Valerie Ellis Lavin

Quick Overview

The StatPacks G3+ Perfusion is a 40-liter hybrid carry EMS bag designed for trained medical professionals who require organized ALS and BLS equipment transport across variable mission profiles, from remote access rescues to vehicle-based emergency response.

The G3+ Perfusion is built around a hybrid carry system that converts between two configurations without tools. Backpack mode deploys foam-molded dual shoulder straps for hands-free movement and ergonomic load distribution over uneven terrain. Sling mode uses a single removable shoulder strap for rapid vehicle deployment and confined-space operations. Stowing the inactive strap set is a required safety step, as loose straps present a documented snag hazard on vehicle doors, debris, and personnel.

Internal architecture supports systematic, repeatable equipment staging through Velcro-lined compartment walls compatible with StatPacks G3+ modular cells. The dual main compartments, separated by a removable rigid shelf, allow heavier trauma supplies to be staged low and high-access diagnostic and airway equipment to be staged at the top. Clear Mono-Mesh pockets on the interior flap enable immediate visual identification of critical supplies under operational stress, reducing search time when it matters most.

The "Stand-Strong" impregnated base is a rigid, waterproof, abrasion-resistant panel that allows the pack to stand vertically on its own, functioning as a self-contained work platform at the patient's side. On inclines or unstable ground, the pack should be laid on its back to prevent tipping. The empty pack weighs approximately 5.7 lbs, and total packed weight must be monitored to prevent structural failure of zippers, seams, or straps during deployment.

Field Application Steps

1. SELECT CARRY CONFIGURATION: Assess your mission profile before leaving the vehicle. Deploy backpack mode for hands-free movement over distance or uneven terrain by clipping the harness straps into the lower D-rings and adjusting for a snug fit. Stow the single shoulder strap completely in the rear panel pocket to eliminate snag hazards.

2. CONFIGURE FOR SLING MODE WHEN APPROPRIATE: For vehicle-based response or confined-space operations, unclip the backpack harness from the D-rings and secure the straps inside the dedicated rear stowage panel. Attach the single heavy-duty shoulder strap to the designated anchor points and configure for single-shoulder or cross-body carry.

3. USE GRAB HANDLES FOR SHORT TRANSFERS: Use the reinforced top or side grab handles when lifting, repositioning, or maneuvering the pack within an ambulance, aircraft cabin, or staging area. Reserve these handles for short-distance movement only, not extended carry under load.

4. STAGE THE PACK AT THE PATIENT'S SIDE: Upon reaching the patient, identify a level surface and place the pack on its Stand-Strong base in the upright tower configuration. This positions all compartments for vertical access and prevents ground contamination of equipment and exterior surfaces.

5. ACCESS EQUIPMENT BY PRIORITY TIER: Open the main compartment zippers fully to expose the clamshell layout. Retrieve primary bleeding control supplies including tourniquets, pressure dressings, and hemostatics from the designated top-tier module first, consistent with your unit's loadout protocol.

6. MANAGE THE REMOVABLE INTERNAL SHELF: Keep the rigid divider installed to maintain the dual-compartment structure for standard loadouts. Remove it only when the mission requires a single large bay, such as for a D-size oxygen cylinder or multiple large dressings.

7. CONVERT TO SLING MODE POST-SCENE: Once the patient is packaged for transport, convert to sling configuration for in-vehicle work. Unclip backpack straps from the lower D-rings, fold and secure them inside the rear stowage panel, attach the single shoulder strap to anchor points, then sling over the shoulder or position the pack on the bench seat for side access.

8. CONDUCT PRE-SHIFT INSPECTION: Before each shift, actuate all zippers and check for damaged teeth or pulls. Physically inspect all straps and buckles for fraying, cracking, or deformation, and confirm all attachment points are secure. Inspect the main fabric body and base panel for rips, punctures, or delamination.

9. DECONTAMINATE AFTER PATIENT CONTACT: Use a service-approved disinfectant wipe or solution to clean all exterior surfaces and the impregnated base after any patient contact call. Do not machine wash the pack. Air dry completely before restocking and returning the system to service.

10. CONDUCT PERIODIC INVENTORY: On a weekly or monthly cycle, completely empty the pack and all modular cells. Confirm all contents against official loadout lists, remove expired or damaged items, clean the interior before repacking, and re-evaluate module placement for maximum operational efficiency.

Equip Yourself: STATPACKS G3+ Perfusion – Hybrid Medic Backpack & Sling (40L)

Ensure you have the right gear before an emergency strikes.

View Product

LEGAL DISCLAIMER & SAFETY WARNING:
The information provided in this Luminary Global Field Manual is strictly for educational and informational purposes. It is not a substitute for formal medical, tactical, or professional training. In the event of a medical emergency, immediately seek professional help or contact emergency services. Luminary Global assumes no liability for the misuse of equipment, improper application of techniques, or any injuries/damages resulting from the use of these guidelines. Always rely on your official agency training, local laws, and established protocols during a crisis.